We got extremely lucky and got a tiny window of cloudless sky in an never ending sequence of cloudy nights. Also the conditions were a nightmare with severe light pollution and lights shining directly at our equipment.

  • Samyang 135mm f2.0
  • Fuji X-T5
  • 158 x 5s
  • ISO 125
  • @f2.8

And maybe somebody here can explain to us what the ionized gas is that 'shoots out‘ in front of the comet?

Also do the colours seem to be correct? We tried our best at background extraction and maintaining the true colour, but the raw data was of poor quality. From images of other comets the dust tails normally seems to have a yellow/orange colour and only the plasma tail is blue.

Edit: found the answer to the Anti-tail. It shows the trail of dust were the comet has traveled, which appears to come out at the opposing side because of earths angle relative to the comet and sun.

  • falkerie71English
    3•2 months ago

    I’m new to astro, is it necessary to stack so much photos to see this comet? Whats the difference between single shot and stacked in this case? Thanks!

    • @bistdunarrischOPEnglish
      5•2 months ago

      The comet is also visible on one single exposure as it is very bright. It was also visible to the naked eye. But stacking reveals even more details because it improves the signal to noise ratio. Also stacking helps removing unwanted objects like satellite trails, planes or moving clouds.

    • @[email protected]English
      2•2 months ago

      This I took holding an iPhone on a picnic table. See the difference? All the details that OP managed to get?

      • falkerie71English
        2•2 months ago

        That’s extremely good for a phone camera I assume. I did try with my own camera a few days ago. I originally asked because weather conditions in my area wasn’t great for a while, and I don’t know what settings to start off with. I did my best at stacking and editing them with Affinity, although not the greatest, I did manage to capture something haha.

        Edit: camera specs
        Fujifilm X-S10 + Sigma 18-50
        ISO640, F/2.8, 5 sec x 140

        • @bistdunarrischOPEnglish
          1•2 months ago

          It‘s hard to tell from your image, bit it appears you can even get a bit more details if you register your lights onto the comet itself and then stack all the images. I used Siril for the two step registration process.

          But nice image nonetheless!

          • falkerie71English
            2•2 months ago

            Thanks! I did try with DSS afterwards to only slightly better results? I’ll give Siril a try too. What do you mean by “register the light to the comet”? Is it a Siril specific setting?

            • @bistdunarrischOPEnglish
              1•2 months ago

              I do not have much experience with DSS, as far as I know the result should be very similar. „Lights“ is the term for a single exposure. The technique is basically the same no matter which software you use.

              But if you have Siril specific questions feel free to drop any questions :)

              • falkerie71English
                1•2 months ago

                Oh okay, so you mean the light frames. Got it.
                Though, I still don’t understand what you mean by “registering the light frames to the comet itself”. I have 140 frames of the comet (albeit not in the same position since I don’t have an astro tripod), and I imported them all into the light frame stack. That’s what I’m supposed to do, or do you mean a more specific step than that?

                Thanks again!

                • @bistdunarrischOPEnglish
                  1•2 months ago

                  Ah ok, so I assumed you registered all your light frames onto your stars as your stars look very sharp. And that’s the normal way for every astro image you would normally do. A comet however moves so fast that its position changes even in the short time frame were you took the images.

                  So after registering all the images with the stars pattern you want to make a second registration were you mark the position of the comet on the first frame and on the last frame. With that now all images are aligned onto the comet and now the stars appear to move in the background. As your stars look so sharp I assumed you didn’t make the second registration. In DSS there is a comet mode for that but I haven’t worked with that so I can’t tell you about the workflow with that program.

                  Hope that helped in any way!

                  • falkerie71English
                    1•2 months ago

                    Oh nah, I did try my best to focus on the stars. They look bright in the photo because I removed the background and cranked up the contrast after stacking in Affinity. It was almost a flat grey image after stacking and before I photoshopped it. Maybe I did fuck up somewhere in the process haha.

                    I only ran through the stacking process once, never encountered a setting/dialogue which told me to select where the comet was. Maybe I’ll play around the program a bit and see some tutorials. There’s no way for me to take comet pictures again where I’m at. Cloudy skies these days 🫤