Bought a Merkur 33C, a synthetic Parker brush, and a mühle soap bar thar I received today.
Not as close a shave as I’m used to, but my skin feels a lot less irritated than it used to after a shave. Cut myself twice, on my upper lip and on the underside of my chin.
How many passes did you do? I’ve found that once you develop your technique and become more comfortable with using a safety razor, the cuts will be fewer and the shave will be closer. I also learned that you do one pass with the grain, a second pass against the grain, and a third across the grain. When I do this not even babies’ bottoms can compare.
Congrats on saving money and the environment (in a small way). You’ll have to figure out responsible disposal of the blades. I took a condensed milk can, carefully pushed a big knife into the top of it, drained it fully, and labeled it “sharps.” I keep this under my sink with a piece of tape over the slot. Each time I retire a blade it goes in the container. Someday my descendants will tape it securely and it will go in the trash (because I’ve been shaving this way for well over a decade and have yet to fill it, but also I really stretch the life of my blades for no good reason).
I get much closer shaves with my Merkur 33c safety razor than I did with cartridges.
I’ll suggest another order: go 1. with, 2. across, then 3. against the hair. Against is the most skin irritating and largest risk of nicks, so may well be done with the least amount of work.
Also, warming the area to be shaved with warm water (or shower as you mentioned) does a lot for the closeness of the shave, don’t skip out.
I find brush and lather mostly to make shaving smoother and lessen skin irritation, not make for closer shaves, but your mileage may vary. Also consider warming your blade (I run it under the warm water) between passes, I find it also helps for the smoothness although can’t say why.
If you have to apply force to the cutting (rather than letting “gravity” do the work) you probably need new blades. They are supposedly single use, but I can typically get 2-3 shaves in on a regular blade, and even up to six shaves with some blades (Korean Dorco platinum is my favorite).
Adding force is the only way I get nicked nowadays, but it goes fast when I do, so I make sure to switch blades even between passes if need be.
Also, depending on your face and skin, you might want to try a safety razor with a different blade angle, there are handles that give a (slightly) more aggressive shave — meaning closer shave but (slightly) higher risk for nicks and irritation.
Best of luck!
I find it so funny that they used to just put a hole in the wall and you would shove old razors in it. A hazard for renovators 60 years later.
Yep, found this in my old house during a renovation
There was a 3 inch deep pile in my wall when i pulled down the tile, weird surprise to find.
Next time (in like 30 years when you finally fill up yiu current can, use the church key method (one medium sized, triangle hole on one side, a smaller on the opposite side) and then after draining/rinsing, use a Dremel to cut a thin slot towards the top.
When you fill that can after 30 years, you just hammer the top down and seal the hole that way.
What razor blades do you use? I started off years ago with Astra ones. They gave a good shave, and I like that I could get 2-3 shaved out of each side (so 4-6 in total per blade) before they became too dull. But they are made in Russia, and for moral reasons I switched to Feather (which are made in Japan). The Feather ones give a great shave, but they are really only useable once per side.
I use these:
https://www.amazon.com/dp/B07Q1JNPRH
I have neither thick not tough hair, so they last me two weeks easily. I also strop them on the underside of my arm in the shower to stretch their life.
I’d always wanted a vintage Gillette or a Merkur but have always been too cheap. I think my original handle was a drugstore special and then I upgraded to an Edwin Jagger. With that handle, my particular hair, and extraordinary lack of skill, I found Astras to be very good (I thought they were made in Türkiye but just checked the box and you’re right - they’re Russian. But my box is probably close to two decades old.) I got some Persona Blues and also found them to be similar to the Astras under the same conditions. I’ve picked up a variety of blades over the years, including Wilkinson Sword (crap, but from a store going out of business sale) and some that I’ve traded with people who also use DE razors.
I never tried Feathers with those handles because I had always read they were mostly for bloodletting and yes, didn’t last very long. Since I changed my handle to a Henson, I’ve found that I can shave with anything because it’s SO forgiving. I could probably cut myself if I tried, but this thing lets me use even Feathers with confidence, and I don’t get ingrown hairs anymore. I can even do my dangly bits safely (yes, even with the Feathers). I’ve posted once or twice about the Henson so I want to be clear that I don’t have a horse in this race, but for me it was a game changer. I think finding a handle that works for my hair type and breathtaking lack of skill, then matching blades to that, was the key.
I’ve also found that DE shaving aficionados just love talking gear, so if you meet anyone IRL see if they would be down to swap blades. I’m sure the shaving companies will also sell you a blade sampler pack.
tl;dr: Persona Blues are probably my favorite, Astra is also great but has some baggage, and give Wilkinson a miss. If you’re using Feather pay attention and don’t let anything startle you.
Thanks for the recommends. Yeah, you definitely have to be careful with Feather blades. Although I only found them a bit more ‘cutty’ than Astra’s.
If a guy wanted a Henson… where would he get one?
Just from their website, but I did a Black Friday special from Grown Man Shave in the US a few years ago - it was $66 for two handles. It was a buy one, get one, and I gave the other one to a friend. In exchange he gave me a Bevel handle that he liked but didn’t love. The Bevel is super heavy, which some people like, because the handle should be doing the work. I haven’t tried it.
Interesting, thank you!
I use… some random double edged safety razor I found on Amazon a few years ago. It’s fine, but I have been thinking about an upgrade.
I did two passes, the same as I did with my plastic Gilette. It’s a skill issue for sure, I have shaved with the same razor for about 16 years, and this shave isn’t that far off from my previous shaves.
Another tip that helped me early on is to not skimp on the lather. I would soak then wring out a washcloth in the hottest water I could get from my tap, or microwave the towel for like 30 seconds (YMMV on timing). Once it is just cool enough to touch I wrap it on my lower face and neck. Do this again between each pass, before lathering. And when lathering, really use that brush. The point is to soften and lift the hair and to open your pores, and I noticed a big difference in how irritated my skin gets if I’m in a rush and don’t do these things. And yeah, git gud lol
I shaved right after a hot shower where I had thoroughly washed my face and beard with s face wash and a scrub. I kept reapplying the lather, but probably got the angle wrong when I cut myself.