Small engines generally don’t, this would be for the starter motor most likely, since snowblowers are infrequently used seasonal machines they often have AC-mains-voltage starters to avoid having to keep a battery charged year round. At least mine does, and it seems like OP’s does as well judging by the “120VAC” marked on the solenoid there. For DC (battery) starers or pull-start engines you don’t need a capacitor. For AC starters you do.
Not sure about the application here, but since its a single phase AC circuit, possibly turning a motor, the capacitor might be used to create a phase shift to turn the motor.
This is how you can run 3 phase induction motor with a single phase.
Esit: and OP has come clean its not a snowblower but a log splitter 😄
AC motors are weird, they’re super simple in some respects, not requiring any sort of internal commutation or switching of coils or magnets on and off because the rising and falling AC naturally does that for them, and that simplicity makes them incredibly reliable and durable for cheap with very few points of failure, but that simplicity can also make them inefficient or even not work properly because perfect, ideal electrical operation will never actually match reality for a motor with inertia, momentum, and load conditions which are essentially dragging it backwards so it starts to fall behind, preventing it from following the exact AC waveform and reaching its ideal synchronization with the AC voltage being supplied to it, ending up with a lot of it being wasted or even working against the motor, and that gives you a weaker and slower motor than you actually want, if it even works at all.
The purpose of the capacitor for an AC motor is basically to compensate for the difference between the motor’s “ideal” perfectly synchronized operation, and the unfortunate realities of physics and the mechanics of the load it’s attached to. An appropriately sized capacitor delays the phase of the AC so instead of peaking when the rotor is still behind the position where it’s ideally going to be (due to the forces dragging on it), it peaks exactly when the motor can get the most leverage out of it.
Now if you’re really clever and understand electrical principles pretty well you’ll realize that this explanation doesn’t fully make logical sense either, and there’s a reason for that. That difference between “ideal” and “reality” also means that at certain points the spinning motor is also acting like a generator and creating back-EMF that counteracts the capacitor and even slows the motor itself down. It’s complicated, and weird. There’s an awful lot at once going on considering it’s such a “simple” design in theory.
In a DC motor, either you’ve got a computer controlling the voltage to the coils directly through sensors or other feedback, or you’ve got a commutator and brushes driving the coils, either way, the same principles are already baked into those designs. They don’t need a capacitor because they’re not relying on an external AC wave and then trying to match it as it goes, the DC voltage just does exactly what you tell it whenever you tell it to, and if you want it to do something at a different time, you just make it do it at a different time. The computer or the commutator ring do the time-shifting for you. In practice, this sort of makes DC motors simpler in some situations, but when you’ve only got AC available and you need relatively high power, it’s still usually not worth the DC conversion.
Note that this is just one way of looking at it, it is not the most technical nor the only explanation for what’s going on. Like I said, AC motors are weird. Motors are weird. Magnets are weird. Electromagnets are weird. Induction is weird. Fucking magnets, how do they work? Doesn’t matter, as long as they do. The capacitor makes sure they work at the right time, and the result is a cheap, powerful, reliable motor.
I didn’t even know small engines had a capacitor!
Small engines generally don’t, this would be for the starter motor most likely, since snowblowers are infrequently used seasonal machines they often have AC-mains-voltage starters to avoid having to keep a battery charged year round. At least mine does, and it seems like OP’s does as well judging by the “120VAC” marked on the solenoid there. For DC (battery) starers or pull-start engines you don’t need a capacitor. For AC starters you do.
Aside from the obvious function of storing a charge, what’s the capacitor’s role in this setup, and why only AC?
Not sure about the application here, but since its a single phase AC circuit, possibly turning a motor, the capacitor might be used to create a phase shift to turn the motor.
This is how you can run 3 phase induction motor with a single phase.
Esit: and OP has come clean its not a snowblower but a log splitter 😄
AC motors are weird, they’re super simple in some respects, not requiring any sort of internal commutation or switching of coils or magnets on and off because the rising and falling AC naturally does that for them, and that simplicity makes them incredibly reliable and durable for cheap with very few points of failure, but that simplicity can also make them inefficient or even not work properly because perfect, ideal electrical operation will never actually match reality for a motor with inertia, momentum, and load conditions which are essentially dragging it backwards so it starts to fall behind, preventing it from following the exact AC waveform and reaching its ideal synchronization with the AC voltage being supplied to it, ending up with a lot of it being wasted or even working against the motor, and that gives you a weaker and slower motor than you actually want, if it even works at all.
The purpose of the capacitor for an AC motor is basically to compensate for the difference between the motor’s “ideal” perfectly synchronized operation, and the unfortunate realities of physics and the mechanics of the load it’s attached to. An appropriately sized capacitor delays the phase of the AC so instead of peaking when the rotor is still behind the position where it’s ideally going to be (due to the forces dragging on it), it peaks exactly when the motor can get the most leverage out of it.
Now if you’re really clever and understand electrical principles pretty well you’ll realize that this explanation doesn’t fully make logical sense either, and there’s a reason for that. That difference between “ideal” and “reality” also means that at certain points the spinning motor is also acting like a generator and creating back-EMF that counteracts the capacitor and even slows the motor itself down. It’s complicated, and weird. There’s an awful lot at once going on considering it’s such a “simple” design in theory.
In a DC motor, either you’ve got a computer controlling the voltage to the coils directly through sensors or other feedback, or you’ve got a commutator and brushes driving the coils, either way, the same principles are already baked into those designs. They don’t need a capacitor because they’re not relying on an external AC wave and then trying to match it as it goes, the DC voltage just does exactly what you tell it whenever you tell it to, and if you want it to do something at a different time, you just make it do it at a different time. The computer or the commutator ring do the time-shifting for you. In practice, this sort of makes DC motors simpler in some situations, but when you’ve only got AC available and you need relatively high power, it’s still usually not worth the DC conversion.
Note that this is just one way of looking at it, it is not the most technical nor the only explanation for what’s going on. Like I said, AC motors are weird. Motors are weird. Magnets are weird. Electromagnets are weird. Induction is weird. Fucking magnets, how do they work? Doesn’t matter, as long as they do. The capacitor makes sure they work at the right time, and the result is a cheap, powerful, reliable motor.