• @[email protected]
    link
    fedilink
    English
    21 year ago

    Good to know there isn’t noticeable distortion then. The frequency responses I have seen look good to me. I definitely hope to see some in depth measurements come out for them! I assume some audiophile creators are getting their hands on them, and I would expect to see reviews in the near future.

    • Avid Amoeba
      link
      fedilink
      2
      edit-2
      1 year ago

      I just checked the latest firmware of their DAC and it has a bit of distortion when driven at the default settings. There’s now an app that allows to adjust the pre gain to eliminate it but then the final output is not very loud. I think this is the reason why they keep the pre gain as high by default. There isn’t a lot of distortion but if you know where to pay attention, you can hear small pops here and there. I’m driving mine with a set of Topping gear. The output is Topping E30 II and that can drive them loud enough without distortion. I’ve dialed in their default PEQ into PulseEffects’s EQ. To be clear, these cans cannot be used without PEQ. That’s part of the trick making a physically imprecise driver to sound good. If you want to use alternate DAC/amplification, you have to replicate the PEQ somewhere along the signal chain.

      • @[email protected]
        link
        fedilink
        English
        21 year ago

        Good to know that it’s not to hard to recreate the EQ. I’m already using EasyEffects convolver effect for my current headphones. I was planning to give the included DAC/AMP a try, but I’d definitely prefer to use my own Schiit stack in the long run. Are you able to share the PEQ you are using?

        • Avid Amoeba
          link
          fedilink
          1
          edit-2
          1 year ago

          You can scoop em up straight from the source:

          ...
                  .f1  = { PEAKING,    {0},    38.5, -21.0,  1.4  },
                  .f2  = { PEAKING,    {0},    60,    -6.7,  0.5  },
                  .f3  = { LOWSHELF,   {0},    105,    5.5,  0.71 },
                  .f4  = { PEAKING,    {0},    280,   -3.5,  1.1  },
                  .f5  = { PEAKING,    {0},    350,   -1.6,  6.0  },
                  .f6  = { PEAKING,    {0},    425,    7.8,  1.3  },
                  .f7  = { PEAKING,    {0},    500,   -2.0,  7.0  },
                  .f8  = { PEAKING,    {0},    690,   -5.5,  3.0  },
                  .f9  = { PEAKING,    {0},   1000,   -2.2,  5.0  },
                  .f10 = { PEAKING,    {0},   1530,   -4.0,  2.5  },
                  .f11 = { PEAKING,    {0},   2250,    6.0,  2.0  },
                  .f12 = { PEAKING,    {0},   3430,  -12.2,  2.0  },
                  .f13 = { PEAKING,    {0},   4800,    4.0,  2.0  },
                  .f14 = { PEAKING,    {0},   6200,  -15.0,  3.0  },
                  .f15 = { HIGHSHELF,  {0},  12000,   -6.0,  0.71 }
          ...
          

          https://github.com/ploopyco/headphones/blob/1e6896f918383854ec5a74e860dd7ed58671cae5/firmware/code/configuration_manager.c#L55

    • Avid Amoeba
      link
      fedilink
      2
      edit-2
      1 year ago

      Here’s another bad measurement I did just now on my EARS. Bad because there are known problems with the EARS like the giant hump at 4.5K which is not due to the headphones but a resonance in the “ear canal” of the EARS. The red is SRH440, and the blue is the Ploopy. One of the graphs has psychoacoustic smoothing applied. The other has no smoothing.

      There’s a hump at 43 which is EQed down and a trough at 420 which is EQed up. They get a lot better in the psychoacoustic view. Again, ignore the gore at 4.5K, that’s strictly a measurement problem.

      My noise floor is bad so the overall noise level is useless but humps in THD are somewhat useful. Here it is:

      There’s a small hump around that trough at 420. Nothing ridiculous overall. The gore at 4.5K is again due to the measuring equipment.

      • @[email protected]
        link
        fedilink
        English
        21 year ago

        Thanks for the measurements! Even with some flaws, these are very helpful for me to get an idea of what to expect!

        • Avid Amoeba
          link
          fedilink
          1
          edit-2
          1 year ago

          So I saw an HE400se on sale and that’s supposed to produce pretty great sound with just a couple of PK filters. So I grabbed a pair. Well it’s pretty good but there’s treble missing that exists in both the SRH440 and Ploopy. It’s the kind of treble that is often attenuated in standard EQ presets with a high shelf like this:

          Filter 6: ON HSC Fc 10000 Hz Gain -2.6 dB Q 0.70