Hi All,

I have a 4TB drive that was originally in a PC connected via SATA. I now wish to put it in an external enclosure and connect it via USB, however this is proving more difficult than I expected, and from what I understand it’s Windows XP’s fault.

On attempting to mount the drive with sudo mount /dev/sdc /mnt, I receive the following error:

mount: /mnt: wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or helper program, or other error.

The output of fdisk -l is as follows:

Disk /dev/sdc: 3.64 TiB, 4000787025920 bytes, 976754645 sectors
Disk model: Expansion Desk
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disklabel type: dos
Disk identifier: 0x00000000

Device     Boot Start        End    Sectors Size Id Type
/dev/sdc1           1 4294967295 4294967295  16T ee GPT

As can be seen, the disk is detected correctly as a 3.64TiB drive, but there is a partition that’s read as 16TB. This, AFAIK, is because the sectors are incorrectly read as 4096 bytes long when they should be 512 bytes, and this is a thing that external enclosures do to ensure MBR compatibility with Windows XP.

I tried overcoming this by mounting as follows:

$ sudo mount -o ro,offset=$((1*512)) /dev/sdc1 /mnt

however now I have a new error:

mount: /mnt: failed to setup loop device for /dev/sdc1.

Trying to mount with sudo mount /dev/sdc1 /mnt only yields

mount: /mnt: special device /dev/sdc1 does not exist.

I’m at a loss as to how to mount this drive - at least, without reformatting it. Is it at all possible? Once I’ve cracked the code, can I configure /etc/fstab to do it automatically for me, or am I stuck in this limbo-land where I have data on my disk that’s only readable with a hacky workaround? As a last resort, I think I can plug it back in via SATA, copy all 4TB off, plug it in via USB, reformat it and copy everything back on, but I want to avoid that hassle.

Edit: Output of fdisk -l when connected via SATA. Note the sector size is now 512 and the drive mounts happily.

Disk /dev/sdb: 3.7 TiB, 4000787030016 bytes, 7814037168 sectors
Disk model: HGST HDN724040AL
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disklabel type: gpt
Disk identifier: 5852E3A7-A2E4-4589-9D93-F8020C2D7E54

Device     Start        End    Sectors  Size Type
/dev/sdb1   2048 7814035455 7814033408  3.7T Linux filesystem
  • @KrapKake
    link
    2
    edit-2
    10 months ago

    Did you try simply mounting /dev/sdc1 without the extra arguments? You also need to make a mount folder in /mnt, so

    sudo mkdir /mnt/mydrive

    Then

    sudo mount /dev/sdc1 /mnt/mydrive

    • I'm Hiding 🇦🇺OP
      link
      fedilink
      110 months ago

      Yes, the last code block in my OP shows the result of attempting to mount /dev/sdc1 normally: mount: /mnt: special device /dev/sdc1 does not exist.

      Though I do not believe it is required as I can mount other drives to /mnt just fine, I have attempted to make /met/tmp and mount there to no avail.