Just wait for an American to tell you how it’s easier to use fractions with imperial. I’ve legit seen them say shit like 3/8 of an inch is easier to think about than 9.5mm.
Valid denominators are 2, 4, 8, 16, or 32. Technically, 64, 128, and 256 are also acceptable, but they are never actually used. For precision greater than 1/32nd, we switch to thousandths, or tenths of thousandths.
~3.2mm. I can’t think of any real world application which needs fraction of a millimeter which doesn’t include ah calculator and some damn exact measuring tools.
Well I’m building a table right now, and it was pretty easy to choose a size for a mortise and tenon in my 3/4" stock, a third of 3/4" is 1/4". If I wanted half its width, that’s 3/8". Mental math is a lot easier than “What’s a third of 19mm.” In the wood shop, I rarely have to divide things by five or ten. I have to divide things by two, three and four a lot.
I’m building a shaker table out of white oak. I milled all my stock to 3/4" thickness.
Just today, I resawed a board to 3/8", or half its original thickness. I glued two boards together to make 3/2" (1 1/2") thick table legs, and I cut mortises 1/3 the thickness of the stock, or a nice even 1/4".
I’m familiar with the metric system, I learned chemistry and physics in metric. I prefer woodworking in fractional inches because metric seems like a bigger pain in the ass
okay then my answer to the hypothetical is 9.5/3, which is every bit as easy to find on any measurement device, or to use for any practical purpose, as 1/24th
No, like I said in my edit, my drafting ruler has a three or four inch long 24ths scale.
Even if it didn’t, having to mark the halfway point between graduations is hardly helpless.
18ths would need two divisions by three, but thankfully dividing a known measured length by three is easy with a piece of string.
There’s a reason millennia of our ancestors used fractional divisions of standard lengths and weights. They can be measured, calculated and double checked (this one is doubly important for stuff that really pisses off metroids like the hogshead/tun) using cheap, universally available tools and deceptively simple mathematics that have been the foundation of what constituted a good education for centuries.
18ths would need two divisions by three, but thankfully dividing a known measured length by three is easy with a piece of string.
what kind of cartoon fantasyland do you live in where it’s easier to find a piece of string than it is a calculator?
also, all of this is assuming you have your drafting ruler to hand
do you carry it around with you in your pocket on a day-to-day basis? some deep fucking pockets you’ve got there, although I suppose you already that to the 1/24th inch
They can be measured, calculated and double checked
my guy, we’re talking about accuracies of millimeters here: you’re not “double checking” your 12" ruler is accurate by slapping your bare carpet gripper up on the drafting table
You know what really gets me about these threads? Everybody being like “Can you believe Americans are stupid enough to comprehend fractions? I’m too smart to comprehend fractions.”
Just wait for an American to tell you how it’s easier to use fractions with imperial. I’ve legit seen them say shit like 3/8 of an inch is easier to think about than 9.5mm.
Above having to add 3/8, 5/16 and 2/3 inch ¬¬
2/3 is not a valid fraction of inches.
Valid denominators are 2, 4, 8, 16, or 32. Technically, 64, 128, and 256 are also acceptable, but they are never actually used. For precision greater than 1/32nd, we switch to thousandths, or tenths of thousandths.
3/8 + 5/16 is 11/16ths.
Quick off the top of your head, what’s a third of 9.5mm?
~3.2mm. I can’t think of any real world application which needs fraction of a millimeter which doesn’t include ah calculator and some damn exact measuring tools.
Quick off the top of your head, why would I use fractions of a cm instead of mm? It’s a workaround for a shit system
Well I’m building a table right now, and it was pretty easy to choose a size for a mortise and tenon in my 3/4" stock, a third of 3/4" is 1/4". If I wanted half its width, that’s 3/8". Mental math is a lot easier than “What’s a third of 19mm.” In the wood shop, I rarely have to divide things by five or ten. I have to divide things by two, three and four a lot.
I don’t know anything about carpentry, so I’ll take your word on it.
My best guess is that the standards are different. For example 2cm stock instead of 1.9. Then only the 1/3 is problematic.
I’m building a shaker table out of white oak. I milled all my stock to 3/4" thickness.
Just today, I resawed a board to 3/8", or half its original thickness. I glued two boards together to make 3/2" (1 1/2") thick table legs, and I cut mortises 1/3 the thickness of the stock, or a nice even 1/4".
I’m familiar with the metric system, I learned chemistry and physics in metric. I prefer woodworking in fractional inches because metric seems like a bigger pain in the ass
We are communicating through writing on an asynchronous web forum.
what’s a 1/3 of 1/8th of an inch?
1/24th.
Fractions of fractions are easy, just multiply the denominators.
okay then my answer to the hypothetical is 9.5/3, which is every bit as easy to find on any measurement device, or to use for any practical purpose, as 1/24th
Well I’m not the person who initially asked you that, I’m just someone who recognizes how easy it is to work with fractions.
Also I have a ruler with 1/12s graduations and while it’s not 24ths, my neighbor has one marked like that.
E: my drafting ruler has a short 24ths scale
so in other words you’re helpless in that situation?
we can play the same game with 1/18th or whatever if you want
No, like I said in my edit, my drafting ruler has a three or four inch long 24ths scale.
Even if it didn’t, having to mark the halfway point between graduations is hardly helpless.
18ths would need two divisions by three, but thankfully dividing a known measured length by three is easy with a piece of string.
There’s a reason millennia of our ancestors used fractional divisions of standard lengths and weights. They can be measured, calculated and double checked (this one is doubly important for stuff that really pisses off metroids like the hogshead/tun) using cheap, universally available tools and deceptively simple mathematics that have been the foundation of what constituted a good education for centuries.
what kind of cartoon fantasyland do you live in where it’s easier to find a piece of string than it is a calculator?
also, all of this is assuming you have your drafting ruler to hand
do you carry it around with you in your pocket on a day-to-day basis? some deep fucking pockets you’ve got there, although I suppose you already that to the 1/24th inch
my guy, we’re talking about accuracies of millimeters here: you’re not “double checking” your 12" ruler is accurate by slapping your bare carpet gripper up on the drafting table
we no longer live in the pre-industrial age
You know what really gets me about these threads? Everybody being like “Can you believe Americans are stupid enough to comprehend fractions? I’m too smart to comprehend fractions.”
thinking that knowing that 1/3 * 1/8 = 1/24 is something that anybody wouldn’t know is stupid
the point is the impracticality of the result being essentially equivalent to 95/3