Been considering a belt driven commuter and wanted to see what you all thought. Thanks!
When I bought an e-bike for my commute I decided to splurge on one with a belt and I regret nothing. You spend less time messing with it and the bike is a lot nicer to work on when you don’t have to worry about getting grease all over your hands. If I was to buy a regular bike I’d see if something with a belt was available within my price range because I like it that much better.
Mind you, I had that bike for less than two years at this point. I don’t know how a belt behaves in the long run.
Any idea how many miles you have on it so far?
769 km (478 mi). I do a lot of work from home so the bike doesn’t see very heavy use.
Yeah, that belt will probably last you for years lol
I have one on my daily commute bike to work
cleaning the chain of my old bike while commuting in rain and winter is a huge hassle and totally worth the higher price of belt drives
What’s your setup? Ideally I’d like to get some sort of mid drive with IGH but I might just pick up something like a Breezer with no motor.
My current bike has no motor and uses a Gates CDX belt drive with a Shimano 8-gears internal gear hub
I believe thats enough, more gears are not neededmy older chain bike had a motor and I could just let the motor do the work if my chain got too rusty/dirty which resulted in higher wear (loose chain)
The Shimano 8 climbs ok?
the Shimano Alfine 8 has 3 gears below the direct drive (I think what that is called? the one similar to a single speed no gears system) which is pretty ok for most hills
interestingly enough the gear translation on the higher gears is quite steep
while I cruise roughly 18 km/h on the direct drive gear, the next higher one already is more like 22-23 km/hthe more expensive Shimano Alfine 11 has 4 gears below the direct drive gear and the higher ones are still steep increases but slightly less
No idea about cheaper internal gears hubs or other brands though
My motorcycle is belt drive. Does that count?
Based on the phrasing of my question, yeah I guess it does lol
What do you have?
deleted by creator
As someone who does not have a belt drive, one of the biggest promotions of them I see is a belt doesn’t stretch, which is true, they just snap. And I could be wrong, but with how they are less maintenance, I don’t see how it isn’t longer repair times when things do break.
I’ve heard they last like, 3000+ miles though
Sometimes chains snap too. But that is an easy to fix it in a pinch if you aren’t in the middle of nowhere. I just walked my bike to the nearest store with basic bike tools (walmart), bought a chain break tool, and used some quick links I had in my bike bag to repair it and get back home. Not sure how easy doing similar repairs would be to do without keeping a spare belt on you.
I have an acoustic bicycle with Gates CDX and Alfine 11 IGH. The use cases for this combo are not for me. The absolute win is the lack of maintenance and no greasy chain. However chain maintenance is a non-issue for me. A little care goes a long way. And I’m familiar enough with bikes to avoid the “chain print.”
My issue with Gates drive is that the drag is very noticeable. A properly tensioned belt introduces a lot of drag. Adding in the drag from the IGH seals, I always feel like a brake is dragging. Another concern for Shimano IGHs is that they can leak when the bike is on its side. This is a non-issue for bicycles in use, but my bike is designed to be packed for airline flight. It’s almost guaranteed that the hub will be vertical during transport, and I’ve had to clean up small oil spills after traveling with my bike.
Changing gear range is expensive and always requires a student/new belt. On a chain drive bike, changing gear range is simple and relatively cheap. So if you’re going the Gates route, try to have a good understanding of your desired gear range before taking delivery.
Finally, repairing a flat tire on the rear is a way more involved process. If you are very familiar with working on belt/IGH bicycles, it’s less of a concern. But changing a tube on the side of the road in the rain in the middle of the night (because OF COURSE that’s when flats tend to happen) is a real pain. The change goes from a two-minute operation with a chain drive to about 12 minutes (for me) with the belt. There are ways to mitigate and reduce flats (Schwalbe Marathon tires, tubeless tires, tire strips…), but these all introduce some other factor(sl that either increase maintenance, require more tools/supplies, or increase rolling resistance.
Are Gates drive bad? No. They carry a lot of benefits for urban commuters. People who don’t work on their own bicycles are an excellent target audience. The system just isn’t for me.
How do you avoid the chain/gear print?
- Proprioception
- Walk, carry, lift, mount, and dismount from the left side of the bike
- Proper Q-factor (distance of pedals from centerline of bike) for your biomechanics
- Roll up your pant leg and/or secure the cuff, or wear knickers or cycling legwear
- Keep your chain cleaned and lubricated with the correct lubricant for your locale, wipe off the excess lube
Thanks, I put a slap bracelet around my ankle sometimes but half the time it gets knocked off. Guess I just need to git good lol.
Try a blousing garter or a Velcro strap. If you use blousing garters, fold over your pant leg, put on the garter, then roll up your pant leg.
I appreciate your sense of humor here. I hope that I didn’t give you the impression of “just git gud!” There are all kinds of bicycle tips and tricks that are difficult or really prolix to convey online.
Not at all, I appreciate your advice!
I thought that said “belt driven computer” and that I was about to enter a very deep rabbit hole lol
I mean, there is the og. Granted it’s less belts, more tapes
