Like most basic entry-level coffee nerds, I do whatever James Hoffman tells me to, so I use ~15g of coffee to 250g of water (which is equivalent to the 1 to 16.7 ratio suggested in your link).

I think it’s still worth playing around with ratios regardless of grinder, it definitely could still make a substantial difference in your cup. However, switching to a decent burr grinder would be a massive difference both in quality of results, but (perhaps more importantly) reproducibility. Blade grinders make it harder to achieve the same grind size every time, and even within a single dose the ground consistency won’t be great.

A caveat I’d like to add: blades are known to produce a lot of fines, which causes higher extraction. So maybe the lower-than-typical ratio you’ve ended up on “compensates” a bit for the high extraction. At the end of the day though, remember: who cares what some website/James Hoffman/random Fediverse users have to say? Do you like the coffee you make?

deleted by creator

I started with 60g/L scaled down to a 28g dose because it’s a good amount of brewed coffee for me and it means a bag of 12oz coffee is 12 cups with a little cushion. That works out to 466g (or ml) of water, but I have found I like it slightly better closer to 450g.

I find that a 16:1 or 17:1 ratio delivers the coffee flavor more reliably. But, most morning I forgo this and do a 20:1 or more just so I have more to drink over time. The higher ratios, being weaker, seem to be more forgiving in terms of bitterness (makes sense cause the flavor is more watered down).

I personally do a 20g:300ml for hot coffee or 20g: ~320ml for iced coffee (only approximate because of the ice cubes)

So that ends up being a 15ml per 1g

Also i think you mixed up coffee and water in your post, isn’t it 12.5g water to 1g coffee.

Does it even matter to adjust the ratio precisely if I don’t have a precision grinder and am using a Krups blade grinder? I am trying to get things as precise as possible.

Consistency allows for reproducible results but there’s diminishing returns at a certain point. My grinder is the type that has a big hopper and runs for χ amount of seconds and I don’t notice a difference even though it can be up to 1g up or down.

With blade grinder, ratio has an effect but the grind quality is definitely effecting more. I go with the 16.7 ratio for years with coarse grind and the coffee is really good every morning.

I’d suggest getting a good burr grinder. That has the biggest effect for getting a quality cup every morning.

Mugen: 1:18 usually, V60: 1:16ish. (Light and medium roasts)

Ratio will depend on preference, equipment, and what coffee you’re brewing, as well as the recipe. In my case I use a bit longer ratio on the Mugen compared to the V60 because it has less bypass (less water gets around the coffee by going through the filter too soon). Generally speaking folks use shorter ratios for darker roasts and longer ratios for lighter roasts.

It gets a little more complicated with iced coffee, because what you’re doing with iced coffee is actually brewing a very short ratio and then diluting it, which gives you a concentration that is similar to what you would normally get, but with lower extraction. (Not necessarily a bad thing!)

Depends on the recipe I’m using, but generally between 1:15 and 1:17 grams coffee:water. I use a manual conical burr (1zpresso KMax) for my pour overs.

I’m using 60g/L, the best ratio in my opinion. I grind it using Timemore C2 and brew it using Hario Switch.

For pour-over I use 350ml (350grams) of filtered water, to 24g of medium course ground coffee.

20:300

I just learned I’m hanging out with the wrong crowd. I’ve always been told I make strong coffee…learning it may have been an inside joke.

I use a French press and (I just measured as I didn’t know) I use 26g coffee to 950ml water. Makes a ratio of about 1:36.

1:12.5 seems really high, imo. I’ve always been told 1:16-1:18 and get good results. I agree with the other comment in that a new grinder is what you should be considering

When I switched to pour-over, I didn’t want to futz with figuring out the proper ratio, so I bought a grinder that produces pre-measured amounts, and a pitcher with measurement lines. So I go with the “2 cups” measurement on both.

…and yes, I know that I’m doing it wrong. ;-P

15 grams of water to 1 gram of beans normally. I might adjust it a little depending on the bean.