• @Zak
    link
    English
    253 months ago

    What I want from a battery soldering iron is a field-replaceable 18650 in the handle, not Webserial.

    • The Pantser
      link
      English
      17
      edit-2
      3 months ago

      Build a 18650 battery bank and plug in a pinecil or ts100. A solder iron with a 18650 would be heavy and uncomfortable for soldering.

      • @Zak
        link
        English
        53 months ago

        I would accept a bit of an awkward balance for being self-contained.

        • @[email protected]
          link
          fedilink
          English
          63 months ago

          You’d want more than one cell. You’d be pulling 23amps from a 4.2v 18650 to give the same 100w at 20v power as you get from a top usbpd power supply.

          There are 18650s that do 30 amps for short bursts, but it would get as hot as the iron and be empty in 5 min

          • @Zak
            link
            English
            23 months ago

            I would not want multiple cells for reasons of ergonomics and convenience.

            I probably don’t need 100W for most field soldering. 60 is plenty, and temperature-controlled soldering irons usually don’t need to pull high current continuously. It would need 60W for maybe 10 seconds when powered on, and when heating something large. The rest of the time, it takes relatively little power to keep the tip hot.

            What I’m describing is, of course not the right tool for production soldering. It’s for field work.

            • @[email protected]
              link
              fedilink
              English
              23 months ago

              I’ve got a Ts80p which is a qc3 usbc soldering iron for that. It’s crazy powerful for it’s size and runs off a pretty small anker powerbank. You could slide that into your sleeve to go portable and one handed

              • @Zak
                link
                English
                13 months ago

                That’s similar to the iFixit iron, as is the less expensive Pinecil.

                Those are probably the best options currently available, but I want something more compact and self-contained.

        • @lefixxx
          link
          English
          13 months ago

          If you need to not have a cable, the butane ones would be a better fit.

          • @Zak
            link
            English
            13 months ago

            Having used a butane iron before, I don’t think it would. They don’t have the temperature control modern digital irons can, and they’re forbidden on flights.

    • @[email protected]
      link
      fedilink
      English
      93 months ago

      I haven’t done the math, how much runtime could you get out of a single 18650? They’re pretty stout, but it seems like they’d be a bit underpowered.

      Milwaukee 12v batteries are 3 cells (I think they’re a little smaller than 18650), and you can run through a battery pretty quick (I believe they’re 1.5AH). Though I don’t know how efficient their heating design is.

      • @Zak
        link
        English
        33 months ago

        Assuming the M12 CP1.5 battery pack, it’s probably three 18650s. Specifically, it’s probably three LG HB series 18650s, which handle high burst loads well, but hold only 1500 mAh. A single Sony VTC6 holds 2/3 the energy of one of those packs. Wait… why am I speculating? Youtubers tear down power tool battery packs on video all the time, and someone did that one. They’re Samsung 15Ms, which are a little worse than HBs.

        Anyway, short runtimes are fine for most field repairs, which is the whole point of something entirely self-contained. Spare batteries can extend it indefinitely, but a battery soldering iron is probably not what I’d pick for extended soldering sessions.

        • @[email protected]
          link
          fedilink
          English
          1
          edit-2
          3 months ago

          Lol, I get it, I often start doing the math and realize “someone has already done this”.

          Cool, thanks for the link. I already knew the little 12v batteries suck (though they work fine for the intended purpose, like impact driver or work light). I kill them with any other tool.

          Yea, I was just thinking is the runtime reasonable enough that having spare batteries is a sufficient approach. Like you said, long runtime isn’t required, 15 minutes total runtime is probably more than enough (though that would be hell on battery life cycle).

          Since I already have a slew of Milwaukee batteries, I’m trying to avoid things with 18650, except where form factor matters (like my flashlights). A Single Battery to Rule Them All (or at least most things).