https://imgchest.com/p/agyvg9qwy89
Been having issues with this Inland PETG. I’ve had so many failed prints. This 230C print temp and 80C build temp print was the least f***ed up print I had so far.
I also adjusted combing to Within Infill and retraction to 7mm at 60mms. All other settings should be default on Elegoo Cura N4P Normal settings
Some of the bridging is fine and there are sections that even look good but the rest are covered in blobs and stringing. The inside as it was printing was making noises and small pieces flew out as it was being scraped and stuff. The top layer shows a bit of what I mean.
I’m kind of new to this and can’t seem to narrow down on what the issues are I found online. I’ve adjusted temps and only made it worse. I raised extruder a bit so that helped. I would like to make it looks as perfect as can be like my PLA prints.
Let me know your thoughts below, I’m happy to try them out.
What’s your print speed? PETG likes it slow, 30mm/s for most hotends.
N4p defaults at 250mms
Not sure what that means but 250 mm/s on that model size is probably impossible. Is that your printer elegoo enptune 4? If you need high retraction distance maybe you have too much play in push fit connectors? But still not worth to look into it if you didnt dry petg yet.
Yes, my printer (neptune 4 pro) has the default speed of 250 mm/s. It prints fine with PLA. I’ve heard many need to increase the speed with PETG so I assumed keeping it the same speed should be fine. Maybe even increasing it.
I believe that could be your main problem. 250 mm/s could be your default travel speed. What slicer are you using? Check all your speeds (travel speed, wall speed, infill speed, etc.)
In slicer you set desired max speed, but you are limited with accelerations and actual size of the model (distance). Printing speed will never be higher than speed you have set, but it can and it will be lower most of the time, depending what are you printing. So if you set 1000 mm/s it will not print that cube any faster. Printer needs some length and time to accelerate to max speed, then slow down before next corner.
Anyway its bad idea to push speed limits while having other issues, leave that for later. In my opinion, 20-30 mm/s is slow printing, 40-70 mm/s normal speed and 80+ fast printing. 100+ is almost impossible for most printers without losing a lot on quality. Check voron, they can push 150 mm/s easy, some even go above 200. Printing faster than 150 mm/s is available for well dialed printers and experienced users. My 2500$ ultimaker barely can do that and failure risk is much higher.
My advice, set speeds at ~60 mm/s or even lower (travel speed 150 mm/s). Find best temps and settings for your filament, try to get desired quality. Try higher speeds after that.
You didnt answer have you dried your filament. PETG tends to soak a lot of moisture and its almost mandatory to have filament drier.
For PETG you dont need higher speeds than PLA for sure. You need higher temps, better dialed retraction and dry filament. If you want to increase speed, you should increase temp accordingly.
If you are unhappy with your max speed, consider switching to 0.6 or 0.8 nozzle. If you need more help its best to provide all information you have (printer model, speeds, temps, filament, any upgrades on printer, etc) to make it easier for everyone.
Well 250mm/s gives pretty good prints for me at least on PLA and I got this printer specifically for the higher rates of speed so I hope petg can handle these speeds as well. As for the filament moisture, I opened a new roll of filament to see if it will change the print but it was the exact same. One of my friends told me that increasing my height by .05mm was a little too high so maybe I should try increasing it .02 mm higher instead. I’ve used lots of temps and found the current one I use to be best out of all of the tests.