Hello Lemmies.

album with photos in order 1-7: https://lensdump.com/a/9Atmx/?sort=title_asc&page=1

EDIT: Direct links may be more convinient pic 1-7

https://i.lensdump.com/i/CbGQ5c.jpeg

https://i1.lensdump.com/i/CbGJv1.jpeg

https://i.lensdump.com/i/CbGtcQ.jpeg

https://i1.lensdump.com/i/CbGrOM.jpeg

https://i1.lensdump.com/i/CbGEDk.jpeg

https://i3.lensdump.com/i/CbGTse.jpeg

https://i2.lensdump.com/i/Cw2uL9.jpeg

I am new to 3d printing as I bought a used Ender3PRO. After initial problems with no adhesion I leveled the bed a couple of tiems. My method is to pinch the paper between the bed and the nozzle to grab and feel a strong friction taking out the paper-sheet. Then in PrusaSlicer I set the Z-offset to 0.2mm and it started printing fine-ish (pic.1, 2, 3 and 4). I made some printer vibrations dampener and figures (around 14 prints ~1,5h each). Next I printed a PS4 Slim Stand (pic.5) and separations between layers appeared.

I increased a bit the temp and run a second piece of the PS4 stand and a dissaster appeared (pic.6) and since then the adhesion to the bed is gone. One in 5 attempts with some glue the filament sticked to the bed, but the next layers have a lot of missplacements and eventually filament sticked arround the nozzle and a destroyed print.

The problems I noticed since the beginning:

  1. adhesion is not great. The nozzle clean line is 80% of attempts dragged with the nozzle to the center of the bed when the brim starts printing. And gets curved just outside the hotend.
  2. a 1-2mm of filament is always outside the nozzle (overextrusion?). I usually clean it with my fingers - wrong?
  3. the printer has a glass bed but I would like to try using the magnetic Ender sheet. The glass is glued to the printer (pic.7)? Can I place the magnetic sheet on the glass? Should I then set Z-offset on the printer settings to avoid nozzle coliding with the bed?
  4. On retraction, the extruder makes a loud click and sometimes a squeak. Is it normal?
  5. I had a hard time to put the filament in the tube of the extruder. Like it was missplaced and had to bend the tip of the filament.
  6. I washed the magnetic sheet with dish-soap and I’ll try my chances today.
  7. The PLA is black, stock Ender3 filament which I suppose is not best quality, but should be sufficient for start… Im also considering moisture in filament as I don’t have a sperate room for my printer. Pic.6 - can it be caused by moisture?
  8. After what happender on Pic.6 the extrusion was really poor which I think was due to clogged nozzle. After heating to 240*C, pulling out the filament, needle-cleaning the nozzle the amount of filament extruded returned to what it was at start.

Some settings:

  • 205C and 60C for first layer
  • 200C and 55C for the rest
  • retraction ON
  • no Z-hop (I’ll try to avoid it for now, since it didn’t help)
  • brim on
  • 0,2 layer height
  • first layer speed 20mm/s, rest ~40mm/s

Any advice welcome and I’ll provide more info if You have any questions.

  • ffhein
    link
    English
    51 year ago

    Thanks! I know several people who know more about 3d printers than myself, but I’ve spent over a year helping people over on the 3D Printing discord so I’ve picked up a few common problems and their usual solutions. And I’ve spent quite a lot of time troubleshooting, calibrating and upgrading my own printer of course.

    But to be honest I’m making an extra effort to be helpful and reply to people because I want communities on Lemmy to get traction :)

    • BalooDK
      link
      English
      31 year ago

      I’m no pro, but I have been printing for some years now. I came here to help out, but your comment said everything that had to be said. Great work. I do hope this is how Lemmy (and this community in particular) is going to be. Thanks to people like you, it’s going in the right direction