• @VelvetStorm
    link
    English
    2011 months ago

    Could have saved me a lot of time if they just said it was 200 bucks at the start of the fuckin article.

    • @[email protected]
      link
      fedilink
      English
      311 months ago

      That might not be that much more expensive. I’ve already replaced my P1 controller due to drift twice (2x$60), which Hall effect sticks prevent.

      • @VelvetStorm
        link
        English
        411 months ago

        Are there not hall sticks you can just put in the old controllers that were drifting? I did that with my joycons.

          • @VelvetStorm
            link
            English
            411 months ago

            The ifixit site has very well-done instructions.

      • @Redfugee
        link
        English
        111 months ago

        Just have it repaired for a fraction of the cost. I had a stick replaced for like 10 bucks.

  • @RightHandOfIkaros
    link
    English
    1411 months ago

    The Elite V2 has nothing to worry about. This thing is uglier and $200 USD.

    • @joshthewaster
      link
      English
      911 months ago

      If hall effect sensors used for the thumbsticks do what they say (no drift) then maybe they do. I have v1 and v2 elite controller and both have bad drift. The v2 is so bad it’s unusable so I use the v1 and just deal with it because I refuse to ever spend another penny on a controller that is just gonna drift again. Hopefully MS will adopt this for all controllers though.

      • @VelvetStorm
        link
        English
        411 months ago

        Those sensors don’t drift.

      • @RightHandOfIkaros
        link
        English
        411 months ago

        Ive had both my Elite controllers since the day they released and I have not developed drift on either. The rubber grips peeled off the V1 I had only a few days before the V2 came out, but I just got replacement grips for it. I dont use my V1 much anymore, but my V2 gets really heavy use and its still fine. I am either the luckiest person on the planet, or the issues aren’t as widespread as people make them out to be, and its just the people with the problem posting about it (as the people with no problems rarely post and generally have no need to).

        HE sensors are nice but they are more expensive and are not immune to developing drift. Over time, the ferro-magnetic material used in the sensors can lose or change their polarity, which can cause very bad effects ranging simply from inaccuracy to inversion. Also, HE sensors are much more susceptible to temperature, and may underperform in areas of high or low heat.

        While generally I might assume HE sensors would be better for a joystick, Microsoft has spent a lot of time and money on the R&D of their controllers. If they decide to use HE sensors in their next controller, then they feel the potential downsides are minimized enough or the performance to cost ratio is better. If they don’t, then HE sensors aren’t worth the cost of using them. Manufacturers spend a lot of time and money in R&D making sure the total cost of their product (including potential warranty repairs they have to do for free) is as low as possible. If they felt the stick drift was expensive enough, they would have done something about it. But since they still use the same modules, the total cost must still be lower than using HE sensors.

      • @[email protected]
        link
        fedilink
        English
        111 months ago

        Have you tried tightening them? I was noticing a small amount of drift in my v2 and just tightened it a little and it feels a lot better.

        Only issue I’ve got now is one I’ve had on a lot of xbox controllers which is the left bumper not registering all the time. I think it’s because of where I press on the bumper it eventually causes it to break over time, I actually replaced the bumpers on my old core controller once and it had indeed broken at the spot where it presses down onto the button on the mb.

    • @slaacaa
      link
      English
      2
      edit-2
      11 months ago

      Looks like my controller for the original Xbox (which was indeed ugly)

    • @FutileRecipe
      link
      English
      1
      edit-2
      11 months ago

      You’re supposed to be watching the monitor as you game, not the controller.

  • @[email protected]
    link
    fedilink
    English
    811 months ago

    Reminds me of when we’d go over to play local co-op games with friends when we were kids. The guests always got the shaft with the half working mad catz controllers and the probably broken turtle beach headphones or other lesser-babka gear. Good memories, though :)

  • @[email protected]
    link
    fedilink
    English
    611 months ago

    Any good hall effect controllers that take AAs yet? Would rather swap out rechargeable batteries than have to plug my controller in

    • AlexanderTheGreatOPM
      link
      English
      111 months ago

      If it’s anything like the elite the charge lasts 40 hours. Put it on the stand after session and it’ll never be close to dead.

  • @Chocrates
    link
    English
    311 months ago

    I don’t see gyros in the specs? A $200 controller without gyros these days? I know that Xbox doesn’t officially support it but still.