I’m printing with PLA on a “PEO” print bed (really a textured PEI), on my heavily modified ender 3, and there’s a pattern on the bottom of my first layer that I’m trying to get rid of. The top of the first layer looks fine, and changing the z offset in either direction doesn’t help. I’ve also tried slowing down the print speed because I thought the extruder might be skipping, but I’m still seeing it at 10mm/s. Any idea what could be causing it, and how to get rid of it?

Pic: https://sh.itjust.works/pictrs/image/31cd6cef-16de-47b3-995f-197f7d0b432d.jpeg

Edit: the first layer went down from the bottom left to the top right, but the pattern I’m seeing is perpendicular to the extruder path

  • FuglyDuckEnglish
    9•15 days ago

    you’re layer adhesion is fine?

    Do you see the pattern in the textured bed? what happens if you get some modeling clay or playdough or a kneading eraser, or anything like it and press it to the plate?

    If it’s not just a texture coming off the build plate (guessing not on your comments?) and it’s not from your z offset/first layer height, then I would look at your temperature settings (might be too hot?) and check that your expected extrusion widths are matching what you are in fact getting.

    • @[email protected]OPEnglish
      6•15 days ago

      Layer adhesion is great.

      No, this pattern isn’t coming from the bed. The bed actually has a polygon pattern that I’m trying to get the plastic to pick up. Sellers on Amazon/ebay/Ali are calling it PEO, but it’s really just PEI with a fine texture that diffracts light. The pattern from the bed comes through really well on the perimeter of anything I print, but not the center.

      I forgot to mention, but I also played with the extrusion multiplier (both directions) and it didn’t make a difference. I’ve also gone through the klipper docs and TeachingTech’s calibration guide, the printer is fairly well calibrated at this point.

      • FuglyDuckEnglish
        4•15 days ago

        How’s your temperature? Could be printing too hot. Both on the nozzle and the bed.

          • FuglyDuckEnglish
            2•15 days ago

            I’d suggest taking it down to 210, 215. a bed at 60 should be normal. If you have one take an IR thermometer and read off a sheet of paper (or a 1-layer print. the thermometers aren’t so good at reading glossy surfaces.) IIRC, for most PLA’s the glass transition temperature is around 70 so 60 should be right there.

            Glass transition is where the plastic begins to soften and be bendable/moldable.

            • @[email protected]OPEnglish
              2•15 days ago

              40/200 looks the same as 60/220. I can try 60/210 but I don’t think it will be any different.

            • @[email protected]OPEnglish
              1•15 days ago

              I tried printing a disk with the bed at 70c and it looks better. Going to try with it even higher. This sheet has a +0.350 z offset compared to my normal PEI sheet, so that might contribute to low heat conduction.

              • FuglyDuckEnglish
                1•15 days ago

                Careful. Too high and you will get failed prints. (Somewhere around the glass transition temp,)

          • @IMALlamaEnglish
            2•15 days ago

            For PETG that’s not that hot. On my i3 clone I was usually 70 bed and 230-235 nozzle. I would try a temp tower and do what looks best. Based on what you’ve said so far, temp does seem like a possible culprit.

              • @IMALlamaEnglish
                1•14 days ago

                Ah, sorry. That does sound a bit hot for PLA. I still suggest a temp tower. If you’re having bed adhesion issues, have you cleaned your bed with dish soap lately? Be sure to use only paper towel to clean/dry it - not a sponge or towel. If that’s impractical, I’ve found Windex to work better than IPA.